Rune 2 forums8/5/2023 ![]() The original design and release of Rune 0.4b was superb - fantastic sound whilst keep it simple for the user by providing a slick and responsive well thought out interface. Sorry if this is bad news but that is simply my view which I hope will provide useful input for future releases especially should Rune V2 emerge. Likewise I tried this Rune Re1 release and simply feel Rune 0.4b is superior in a few interface areas at the moment. I tried Volumio and simply feel Rune 0.4b is far superior with regards to the user interface (Volumio simply felt somewhat clunky). I have no relation with PI or Topping and am simply a more than aging hardware / software developer rediscovering the joy of High Res Music (read Eagles).įor the record my main priority is sound followed by usability (which is why most of us are here I believe). I know this is subjective but I have been extremely pleased with Rune 0.4b on a PI 3B combined with a Topping D10 DAC. How many songs have you got for 10 hours database build, by the way? Or you run it again for the whole NAS without copying anything. If you have mpd.db file already built, copy it to replace one of the 2 files. If all are good and found, it's doing fine. mnt/MPD/USB/?/mpd/mpd.db ( ? = USB label ) (A few seconds for MPD to build database) Create a new share with just a few albums. You cannot update Library on USB if there's no music files in it. NAS mounts should be remounted automatically after reboot. You don't have to copy anything if you built MPD / Library database on this new version.Ĭopy mpd.db file to USB drive only if you already have the MPD database built before install this version and it takes a long time to rebuild. I copied the file into the usb but if i try to update the library on the usb it says it isnt there. Afterwards I shut off the raspberry pie and the nas is gone. Took 10 hrs to build the mpd file from my nas. i2s module setup with auto select MPD output on reboot Unified hostname for all services: System, Access point, AirPlay, Samba, uPnP/DLNA Complete IP address info with QR codes. Improved mount / unmount / remount / remove mount Network Hardware/software volume set automatically for each device. I2S audio output selected automatically after setup in System and reboot. Toggle descriptions with question mark button. Options visible/accessible only when features enabled. Enable / disable / options: applied immediately, no more Ok buttons. Disable features if not use to lower CPU usage: On your router, pre-assign an IP address for RuneAudio to keep it from changing. Get IP address: Menu > Network > Network Interfaces list With RPi accesspoint only if there's no router- Connect to RuneAudio with IP address instead of runeaudio.local Use only amplifier volume.- RPi to router connection: Drag Library home blocks to arrange order (Use Coverart for playback controls instead - tap top-center of Coverart for guide.) Hide top-bottom bars, Time, Volume, Buttons If security of your Wi-Fi is wep, replace wpa as well. ![]() Replace NAME and PASSWORD with ones for your Wi-Fi RPi Zero or wired LAN not possible - Pre-configure Wi-Fi connection Temporarily connect wired LAN then remove after Wi-Fi connected successfully. Write the file to a micro SD card, 4GB or more, with Win32 Disk Imager or Etcher. Decompress to RuneAudio+R_e2-RPiN.img with 7-zip, WinRAR or WinZip Available as image files and RuneOS - DIY RuneAudio+R eĪs of 20200403, RuneAudio+R e2 has been upgraded to RuneAudio+R e3. System-wide upgraded to the latest kernel and packages Complete backend rebuilt with latest Arch Linux Arm ![]() For all Raspberry Pi: Zero, 1, 2, 3 and 4
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |